Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
our current network provider says that they have a restriction on their sim profile so that the mtu should be less than 1430. however things like pdn_dynamic_params_get()...
Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
Hi, I am starting to get into the Nordic world and want to design my first pcb with nordic chips. I would like to get a review on my schematics and the pcb. I am mostly interested...
[Corrected 2026-09-11] This post originally attributed an MPU fault to the missing 7c4ea9a9d5. That was wrong — backporting it did not stop the fault, which looks like a separate...
Hello Nordic Support,
I need version-specific troubleshooting advice for an nRF52840 DK, PCA10056 hardware v3.0.3 (label 2026.16), with the nRF5340 interface MCU. I have...
nPM1300 LOADSW1/LDO1 quiescent current issue — XIAO nRF54LM20A Sense
Status: unresolved as of 2026-08-27. Written to summarize the investigation for external reference ...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello,
we are trying the nRF93M1 DK hw rev. 0.4.0
As suggested, we wanted to build the following sample: https://nrfconnectdocs.nordicsemi.com/ncs/latest/nrf/samples/nrf93m1dk...
Dear Nordic,
As per the RED, article 3.3 www.intertek.com.hk/.../ item (d) radio equipment does not harm the network or its functioning nor misuse network resources, thereby...
We're running a small voice-activity model on the Axon NPU (nRF54LM20B, NCS 3.4.0, Edge AI Add-on v2.3.0, Axon compiler 1.5.0) for a body-worn voice device. Features come...
