Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear Members,
I want to use SPI LCD and Sdcard, they have different CS, but sharing the same SPI ports, I have used different SPI instance but not giving us a good response...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
I am working on OTA update .
Right now i am working simple
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hi,
Is there any command for reading the type of Nordic SoCs (e.g, nRF52833 or nRF52840) that is going to be programmed by nrfjprog/ J-Link Commander?
Thank you!
Hi Nordic,
I want to write a value from the application layer to the bootloader flash region through uart, and use this value to replace the button 4's function of entering...
Hi All,
I'm using buttonless DFU for upgrading the firmware and my requirement is I would like to know the time taken for complete DFU from my application.
One approach...
Hi, I am working on designing specifications for a new product, which will potentially be using the NRF9160 as the main processor, since the main application is centered around...
Dear Nordic support,
We are trying to know the current consumption during BLE RX & TX. However, there appears to be apparently conflicting information. Which is right...
Hi,
I want to use a single firmware to be flashed on two devices that can be used as a ble peripheral with DK Button 3 and as a central with DK Button 4 .
I chose ble_app_multirole_lesc...
Hi guys,
i am using nrf52840 controller.
and in that i have mbe at 0x0000000 location.
i have two bootloader stage. that boot1 and boot 2.
boot 1 i am using to validate...
I have gotten the FDS_ERR_NO_PAGES issue multiple times now. In our last pre-production run, it randomly happened to a few units (4 out of 60). For 3 of the units, the error...
