I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I have an RTOS application into which I integrated a custom BLE service code. Question is, there isn't any need for a separate thread for handling BLE stuff? I see BLE events...
Hi,
I am trying to use UART APIs in blocking mode to receive data from another controller.
I intend to have a timeout on receiving function so not to stuck if no byte...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am investigating the data bit and stop bit settings. At that time, I found a page...
Hi !
I try to use VSCode but any examples return same error:
"Linking C executable zephyr\zephyr_prebuilt.elf FAILED: zephyr/zephyr_prebuilt.elf zephyr/zephyr_prebuilt...
Hi,
As the title states, VS code doesn't recognize includes related to Zephyr.
I've walked through the entire setup guide and installed all components using the toolchain...
So I came across an issue while working on developing an app that can update firmware OTA. I was using Nordic Semi - android DFU Library
implementation 'no.nordicsemi.android...
hi，
1.Now I am using Wireshark to capture nrF52840 DK ZigBee packets. I have configured the environment according to the guide. In wireshark, "nRF Sniffer for 802.15.4"...
hi，
we are using52833 QFN40 to test carrier,but the program will loop at as the picture bellow,while it runs well in 52833 QQFN73 in another board, why? Coutl you help me...
Hello,
Our modem consumes a lot of current when we use a simcard from a provider 1 (a MNO), much more that when we use a simcard from another provider 2 (a roaming service...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
We need fast response from peripheral to central. That means we need a fast connection interval. We are using less than 100mS. But that results in an unacceptable battery...
Hi I have a question regarding USB port on the nrf52840 device When connecting a new device to computer is it possible to tell PC to assigne the same COM port number as last...
