Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
https://devzone.nordicsemi.com/f/nordic-q-a/65059/buttonless-dfu-on-nrf52832
When I try to DFU from NORDIC_BUTTONLESS , nRFConnect disconnects from it and connects to DFUTARG...
Hello,
I get an error message when running this function:
int ret = i2c_reg_write_byte(data->dev, cfg->i2c_addr, LSM6DSOX_INT1_CTRL, test);
I know 0x0BAE0002 error means...
Hello, With nRF5 SDK 17.1.0 release a new ifdef NRF_BLE_LESC_GENERATE_NEW_KEYS in nrf_ble_lesc.c has been added. Could you please clarify what the intention is of this generating...
Hello Team Nordic,
I think there is still a problem in the SDK 17.1.0 if not using a Softdevice (with SD all is OK):
in "nrf_drv_clock.c" -> "nrf_drv_clock_init(void)...
Hello Nordic team,
I am building an IoT solution and plan to use the nrf9160 just as a stand alone modem. App will reside on a separate MCU and talk to Nrf9160 on uart...
HI,
I am developing weight scale with Bluetooth feature. I have already developed the code to get weight scale reading using SPI example.
Also tested ble_app_uart code...
Hello,
I have currently cloned and built the latest master branch of Eclipse MQTT-SN Gateway https://github.com/eclipse/paho.mqtt-sn.embedded-c.git on my Nordic Border...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.4.0 to 1.5.1) and the Modem firmware (1.2.2 to 1.2.3) on my nrf9160 DK devices, the date time isn't synchronized...
Hello there,
It is actually basic for the Bluetooth connection for the nrf52840 using Zephyr, which changed the scan filter by name based on the central UART sample.
As...
Hi there,
We are currently using IAR embedded workbecnh IDE for our development on non-Nordic products. We are thus considering the possibility of also porting our Nordic...
Hi Nordic Support,
I am getting zero distance value from sensor(vl53l0x). I used SLAVE_ADDRESS =0x29 and register address=0x01. My code is mentioned below
void data_handler...
We originally saw (and reported) this problem with nRF5 SDK 4.1.0. We switched to nRF Connect SDK 1.6.0 which did not exhibit this problem. Now we just tested with nRF Connect...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
