Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I'm trying to include a byte in the advertised data that indicates on which channel the advertisement is being sent, 0 = channel 37, 1 = channel 38, 2 = channel 39...
Hi,
We have a board with an nRF52840 working as the primary MCU which controls an nRF9160 via AT commands.
P109 from nRF52840 is connected to the nRESET of nRF9160. To...
Using the GPS sample application as a base, I examined the behavior of "concurrent" cellular and GNSS. I enabled cellular with at+cfun=21 after a GPS fix was obtained. I also...
Hello!
I'm currently working with Zephyr on a custom board based on the RAK5010 board. This board (RAK5010) is currently supported by the Zephyr project,uses the NRF52840...
Good day i am new to Nordics platform and SDK also new to segger embedded studio
i am required to develop a solution that receives data on the UART of the NRF52840(client...
Hi,
I have PCA63511 Power Profiling DK and nRF52840 DK ( and nRF9160-DK )
I was using SoftDevice SDK, and no issues with measuring nRF52840 device. But now I switched...
As state in the title I am trying to run pc-ble-driver on nRF52840 Dongle running examples on Mac OSX.
I uploaded connectivity_4.1.4_usb_with_s140_6.1.1.hex file on my dongle...
Dear:
Do you have any cases about wireless serial port printing debugging at nRF52832 BLE device ？
When the device is not connected to the debugging line, the dongle can...
Hello everyone,
Im developing a simple BLE scanner and its purpose is to receive and send beacons data by serial port.
My application worked quite well when flashing to...
Hello,
I have been trying to debug a curious behavior leading to higher energy consumption (~17mA) on my Sleepy End Device (Rx is off when idle).
I am using the nRF SDK...
Hi There,
If I want to put some files, like video on the nRF52840 boards, and let them broadcast onto other devices. How can I do to find the flash path of the video file...
I'm having a hard time getting nrfjprog to remain in my PATH env variable when using the Toolchain manager. I am following this post -- I am able to `echo` my PATH variable...
Hi
I am usig a nRF52840 with the chip antenna 2450AT18D0100E (Johanson Technology).
How should I calculate the matching filter? I used the values from the reference design...
Hi all,
We met a problem with uart while producting our device. It happened when we communicating with our NB module(BC28), then i catch the waveform by the oscilloscope...
