Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi guys.
I wonder the program run start from which section and how to enter the app when 52840 poweron? Start from SofeDevice?
I only flashed ble_app_uart and SoftDevice...
Hi all,
I'm trying to transfer my custom project pca10056 (which is to broadcast a beacon) to nRF52811 hardware and I'm facing some issues in the last stage of build.
...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
Dear All,
I am working on interfacing BME680 with nRF52840-DK board. I got the output for Temperature, Pressure and Humidity but not getting the output for Gas resistance...
What should be considered for choosing a chipset? the followings are in my mind. Could you please tell me if I am correct and if I should consider anything else too.
1)...
Hi guys.
I flashed a uart-dfu Bootloader(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart), when the program run...
Can you, please, point me towards documentation and (if available) samples of mobile app that would allow me to commission and then interact with devices in RF52840-based...
Hi everyone,
So currently, i am working on a project relating to sending some message from one router to another. I found out that there is a function to create your own...
Hello everyone,
I've been struggling to use the Bluetooth UART example and the RTC2 module but so far I haven't succeeded.
Either I have Bluetooth, or RTC2, but not both...
Hello -
I have created a project with both a SoftDevice S132 and nRF Crypto libraries. All has gone well so far. I am now trying to implementing RNG, following the example...
