We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm trying to implement an immutable bootloader + MCUBoot + (SPM and APP), and then update the app via fota.
My implementation is based on the asset_tracker_v2 example....
Hi,
I'm working on an app where I need to collect data from a sensor, and send it over NUS every 10ms.
I'm using nRF5340-DK (0.11.0), and I'm using nRF Connect SDK v1...
Hi,
I need help to clarify the API for IAS zone server. If I can get example implementation, it would be great.
I have hard time understanding how zb_ias_zone_app_callback_t...
Hi,
I am new to nRF9160DK . I want to set RTC time for the nRF9160DK.
In the application we are getting UTC time from NTP server and we need to set RTC .
I have referred...
Hello,
I am trying to get my nRF9160 to connect to a https server via AT commands, but this is as far as I've been able to get.
In the end this will be used in a project...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
Using SD S140 7.2.0 SDK 17 (nRF52840).
I cannot write to internal flash addresses above 0x78000.
I am calling nrf_fstorage_init setting start_addr=0x68000 and end_addr...
Hello,
I am looking at the TX start-up current for the nRF5340 mentioned here (last 2 entries in the Radio current consumption (Transmitter) table) in the product specification...
Hello,
I am having an issue where I am trying to send a payload in the ACK in the ESB protocol. The issue is when the PRX gets a payload it was not expecting (i.e anything...
Hi Nordic team,
Please guide to resolve the error .
While trying to convert the model_handler.c to model_handler.cpp the below deceleration shows multiple compilation...
Summary: What are advantage bullet factors of Zephyr RTOS over FreeRTOS to choose this in nRF Connect SDK v1.5.0
Details: We have Implemented our previous project...
Due to a particularly stupid thing I have done on another chip, I have ended up depending on the ability to advertise a short name and a long name. However, when I build an...
I'm new to using micro controllers and for a project i have the nRF52 controller and i am trying to perform an OTA FW update using web bluetooth. When i connect to the board...
The problem is I can't figure out a way to use the shield pins on the board (P20) to program an external MCU (nrf52832). It just refuses to do so it always programs the onboard...
