Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi, I am trying to integrate DWS3000 (UWB) APIs, given here to nRF52840 with BLE stack enabled such that my firmware can blink Eddystone packets at the same time when UWB...
The customer requested that pairing be prohibited under certain circumstances, so I called API
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP...
in ~/ncs/zephyr/samples/hello_world/prj.conf or in ~/ncs/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160ns_defconfig
CONFIG_I2C=y
in my nrf9160dk_nrf9160ns.overlay...
Hi,
We are using nrf52833 for measuring angle of arrival. We got IQ samples from the device we need to calculate the phase difference from that IQ sample. please explain...
Hi, we have an application using an nRF52832 without a SD that we want to put into low power / sleep mode to save battery.
What commands should we use to do this and wake...
Hi,
I am using ppi to read some continuous data from a sensor through SPI and i got it working, it reads data in evry 8ms from the sensor through ppi.
but it fails when...
I am working with the secure bootloader example. I copied the firmware zip package to my phone. It contains only application.hex in the package, there is no softdevice or...
Hi,
I am working on an application where the device will be in off mode(only timer and BSP initialized in main ) initially and when I long press button_0 for 5 sec the remaining...
Hi,
We are looking for DFU mode GATT protocol source code for reference to implement custom android application which uses DFU mode GATT service to update firmware distribution...
My static code analysis tool complained something, so I took a deeper look and found the following declaration inconsistencies as of nRF5 SDK v17.0.2 in the DTM area. So I...
I am in the process of programming the MAX30105 sensor with the NRF52840 board to obtain the oxygen concentration values I tried to use the library that already exists in...
Hi ,
I am trying to connect my NRF52840 with the application NRF Toolbox using bleuutooth technology when I use this DK
it works very well and the application detect...
I have an nRF5340 DK board. I have followed the online installation instructions and *believe* I have successfully installed (win 10) nRF Connect and Segger Embedded Studio...
Hello, I'm routing on the nRF52833-QI. I want my RF track (ball H23) to go without bends. I don't use J24 ball. Can I remove the ball J24? What is your suggestion? Best regards...
