Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
how to unpair our nrf52 device once it's paired with another nrf52 device, currently we need to switch off the device so that we can pair another device.
Hi all,
I have a customer that has requested NRC tap to pair functionality for their device, mostly for convenience. This is fine, but I'd like to know what they're getting...
Hi,
We are running into a weird issue with some our devices when they are in the bootloader.
The bootloader fails with this error in nrf_dfu_validation.c: Invalid protocol...
Hello,
We have a firmware with 2 versions that runs on Baremetal and FreeRTOS on nRF52840 DK. We would like to port this firmware to nRF9160 without Zephyr and continue...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
