Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am currently trying to connect an accelerometer to my Nordic board, but I am having some issues with #define NRFX_TWI_INSTANCE(id)
.p_twi = NRFX_CONCAT_2(NRF_TWI, id)...
My problem is with examples of publishing and subscribing at the same time. I crossed them by adding a check for subscription if I did not sign I do this and register the...
Hi guys. I'm fairly new at embedded development and I'm basically trying to set up a workflow that goes like this:
Toggle a GPIO high - low, with a duty cycle of ~500...
I have been following the "Getting started with Nordic's Secure DFU bootloader, a step by step guide". I believe I may have compiled and loaded a DFU bootloader to the nRF52840...
Good afternoon,
I'm working on troubleshooting an issue we're having in the field. We are using the CLI libraries to provide an nRF52840-based board with an interface to...
Hi all,
I need to directly develop my application on top if IEEE 802.15.4 MAC layer. Could you please inform me of any sample application available under Zephyr that directly...
Device: nRF52840
SDK: 16.0
Softdevice: ANT_s340_nrf52840_6.1.1
Hello, We have a master and several slaves setup in a simple master/slave channel configuration. It seems...
Hi,
Can u suggest the procedure to implement key refresh procedure with the sample network using nrf mesh app.
No where i found option in nrf mesh app.
Thanks in Advance...
Hi,
We have 2 projects in pre-production stage that use nRF52840. We are also using FreeRTOS for both projects.
Now we need to create an OTA bootloader for both. There...
SDK: 17.0.0
Hardware: E-Byte E73-2G4M04S1B module
Chipset: NRF52832 QFAA QFN48
Running the hids examples, I noticed that the hids_mouse example will go from Fast Adv...
Do I need to carry out ANSI C63.27 regulatory test for coexistence of wireless communication that share the 2.45GHz band if we designed a custom PCB BLE antenna for NRF52840...
Hi,
I have the nRFgo Starter Kit with the radio module (nRF2427LE1) attached. First, does the radio module not have a bootloader already downloaded to it? Next, when I...
Dear Support Team.
We want to support secure DFU on mobile and desktop platforms. Do you have any documentation to implement this on Mac OSX and Windows?
Its an open...
Hi, is there any LE audio sample for NRF5340?
I know the upper layer protocol is under developing on Bluetooth SIG, but is there any possible way to direct use the HCI command...
