We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Is it possible to have 2 timers (TIMER3 and TIMER4) with the exact timer value?
I need to have two gpios toggeling at a difference time frequency but based on the same clock...
Hello,is the 3.9nH inductance and 0.8pF capacitance in the official routine the impedance matching of the antenna, or do I need additional antenna impedance matching?
I am designing the RF matching network with an IFA antenna for the nRF52811-CAAA.
ANT output may be DC coupled to ground with the IFA antenna or do I need a decoupling capacitor...
Hi folks,
We have a project based on an nRF52833, on a custom board, running at 1.8V. There is no Bluetooth (so no SD usage), and the HF and LF clocks are running from...
I connected nrf52833 with a button and a LED on breadboard, using ble_app_uart example to send message between phone and board. How can I make a function that whenever I press...
Hello Nordic community,
I am using nRF52840 and try to implement external memory unit for MX35LF2G14AC, which is 2Gb SLC NAND flash. I am wondering nRF52840 can support...
For example I want to turn on LED whenever I send 'a' text from my phone. How could I do cause I do not know where a message is stored. I am using ble_app_uart example
It would be useful to read and write other local files apart from the default 'logger', say, to maintain separate custom logs for multiple discovered devices. However modules...
hi,
I coded BT832AF module using nrf52832 eval board and i get the bluetooth device name but i'am not able to connect to BT832 device using nrf tool box it keeps on connecting...
I need a gpio to control an external peripheral.
I thought to code should be similar to controlling one of the leds.
board overlay:
&gpio17 { status = "okay" gpio17...
Hello ! When I run the direct test mode example found in "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8" in transmission mode, does it only transmit packages on a channel...
Hi,
What is the correct way to write to UICR at runtime?
I am using the code below but the MCU crashes on the first line with no call stack trace.
NRF_NVMC->CONFIG ...
Hi,
I'm trying to collect data for average latency for nRF52840 using an Android Smartphone as Central and nRF as peripheral.
Latency is being measured by the Android...
Hello,
I want to send data via Bluetooth Serial as well as USB CDC Serial and currently, I am getting data rates up to 3.2KB/s on a Windows Laptop. I read this https://devzone...
Hi Community,
Facing the RF functionality issue on nRF52833 on our custom board.
Our board is functioning well with nRF52840, then it failed after migration to nRF52833...
