Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello
When I send data over BLE, I got this messages in debug terminal.
<info> app: Debug logging for UART over RTT started. <info> app: Connected <info> app: Data len...
I have seen other post on this issue but they are not helping. I am using the bmd 330 to run ble_app_uart. It compiles and advertises correctly but does not send the tx and...
Hi,
I am facing issues in Flash Data Storage (FDS).
Here, nrf_fstorage_write function is returns with NRF_SUCCESS but not writing in actual memory location. While nrf_fstorage_is_busy...
Hi. I am now at the stage of creating a new project. I want to include DFU over the air support in it. So, how can I do this using the example of two projects (secure_bootloader_ble_s132_pca10040...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
I'm designing a product which incorporates a magnetic sensor (MMC5633) and a Bluetooth microcontroller (NRF52832). The sensor and bluetooth chip share the same ground plane...
hi,
We have some products that have been sold out(hardware:52832,software:sdk13,softdevice:s132_4.0.3).I want to upgrade their sdk to 15.3 through DFU.I learned in the official...
Hello,
I'm trying to modify the current ASSET_TRACKER of SDK v1.4.1 to get it to work in my own server on AWS-IoT.
I'm wondering if there is any documentation about this...
use SDK17.
central uses nRF52832 and peripheral uses nRF52810.
I want to implement the exchange of data with each other.
First, the central scanned and connected.
...
While using NRF52840 SDK with twi_scanner i am able to see i2c address 0x68, but while using zephyr unable to get the data.
I have seen I can configure i2c pins in board...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
