Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
I am using a custom board with nRF8001, where I use external interrupt from the RDYN pin to let MCU know BLE has an event. MCU can recognize these events and change the associated...
Hi,
I added the feature of the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
After programmed the built image to the EV board PCA10040, it could run normally...
Hi
I have 2 customised board with nrf52832, I wanted to communicate between 2 devices. Like to send commands like turn on/off LED from my one board to on/off LED on my second...
hi
i want to use iic in my project ,and i add iic func to my project refrence project twi_sensor.
the code of iic like this：
I call the api in the main
then...
Hello
I would like to use the extended advertisement feature of BLE 5 but I have several questions: 1. If I want to broadcast data in "extended advertisement" messages ...
Hi,
My devices are currently using NRF52832 with SDK17.0.0.
I want to communicate with my devices even when the app is killed by the Android system.
At this moment,...
Please tell me. The NRF24 transmitter is in the one pipe in channel one, sends data to the receiver without confirmation of delivery at a speed of 250 kbps. 1 How long will...
Hello.
I need some documents that i can understand what is going on on the backward when/while two devices are communicating with each other or when/while a device advertising...
We're just finishing our layout for a custom nRF52832 board. According to the "General PCB design guidlines for nRF52 series" we copied the complete nRF layout from your reference...
