I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
Hello,
The Power Profiler Kit(PPK) is not able to measure current consumption. I got this notification asking to reprogrammed the device, I clicked yes and then-after it...
Hi All,
I am currently in the process of designing the PAB layout for my design. My schematic follows the reference design 4 recommended by Nordic.
In this VDD_HV (From...
Device: nRF52832
SoftDevice: S132, 7.0.1
SDK: 16.0.0
I want change DEVICE_NAME by nRF Connect APP, then I add below code, but I found it die here "wait_for_flash_ready...
Hi everyone,
I am working on a project where I have to enter the system into System OFF mode and RAM retention. What I actually want is to retain the value of some variables...
I am using the NRF52840 and SDK15.3. My goal is to sign a payload using RSA and then verify on the NRF side of things.
The signing scheme is done with openssl on my computer...
Hello!
Is it possible to supply the Nordic Thingy:52 board from an external supply, different than the battery (for example, through the USB)?
I only see the battery option...
Hi all,
I wanna connect an accelerometer sensor the nRF52840 DK board. I think it should be connected physically at the pins P0.17, P0.19-P0.23. But the thing is, those...
hello Nordic
i want to use the bl652 laird development board (nrf52832) as a debugger for the nrf52840 dongle
i have been working with that board allready so it has...
Hi,
I'm trying to implement Eddystone beacons in my application.
My application is already contains advertisement feature with whitelist.
When I'm trying to use...
Hello,
Does anyone have some recommendations about what crystal to use with nRF52840?
We have been using FA-20H 32.0000MF10Z-AJ0 but now it is not in stock and we need...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
