I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi, I'm developing new project, and during test I see that, if you quicly connect/disconnect/connect.... and so on, the app seems locked... Tu exclude my HW-FW, I tried same...
Hi,
How to auto-connect with my BLE peripheral without an external application?
Here, the Android mobile acts as a central, and the nordic chip act as a peripheral.
...
SDK15.0.0/SEGGER/Windows
Hi, I ran this example: https://github.com/NordicPlayground/nRF52-ble-long-range-demo .
Note: Added NRF_LOG_INFO("%s", p_adv_report->data.p_data...
Hi, I have a problem with DFU upgrade over BLE on nRF52840dk. For some reason,the upload speed is quite slow ~0.4kB/s. For this test,I used SMP server app and did the compilation...
I'm using DFU of 52840, .I find a question, my development board can work normal with ble_app_buttonless_dfu of nRF5_SDK_15.0.0_a53641a,but my product board can't work well...
When building an app with mcuboot as part of a multi-image build, how can I pass the app version to imgtool so the app_update.bin header gets created with the correct app...
Hello,
I am using a custom nRF52840 (SDK 14.2.0, SoftDevice S140) based board.
Our boards stopped advertising and upon debugging we saw an error in the peer_manager_init...
I am testing the product's DFU using nRF52832.
Select File disappears after downloading nRF ToolBox App once.
Is there any way to not disappear from nRF ToolBox?
If...
Can I use P0.21 as a regular GPIO ? When I power the chip up, will it start correctly ? Is there any problem if I connect it to a LED and resistor ? How do I configure this...
I'm using the NRF52840 SDK 15.0.0
I have 2 task threads and 5 ble services.
Now what happens is when I'm trying to connect the device with 2 tasks and ble services I'm...
Hello,
Is it possible to read the received byte if the parity error occurs? Because I want to receive 9-bit data on UART and get the 9-th bit based of error?
Dear
I am trying to locate the data area of application code from device (nRF52840).
From here , it show me the bootloader will locate at from 0x000 F 8000 – 0x000F E000...
I've been writing a vendor model for Bluetooth mesh based on the light lightness model in the SDK. I'm extending the generic level model into my model - a window openess level...
Hello -
I am trying to set up the nRF9160 DK kit. I successfully updated the firmware and entered the ICCID, PUK, IMEI, and HWID values. When registering for nRF Cloud,...
