Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I am trying to get a BMX160 working over SPI. I was following this post to make this code using the SPI example from the SDK as a basis. I am using SDK 15.3 with a nRF52840...
The app is foreground -> I am very easily connected with BLE device.
The app is in the background -> I get the callback and connect with the BLE device
The app is removed...
Hello.
I'm trying to get the example bootloader Segger project (secure_bootloader_ble_s132_pca10040) running on a custom board I have that uses the nRF52832 as its core...
I am working on nRF9160 and i found that when i change prj.conf, i need to rebuild code. if rebuild is not done(only build is done), changes made in prj.conf does not comes...
Hi
I'm currently evaluating the possibility of using nRF5340 in an upcoming project. As the chip is very new it's easy to understand that all specifications are not yet...
Hello, I am using nRF SDK for Mesh 3.1 and nRF52940 SoC. I have two nodes in my network which both act as a client and a server. Both of them subscribes and publishes to same...
Hi,
I am working with ANT bpwr tx profile and trying to implement HX711 and TWI sensor to it. TWI sensor is already working, but when I add library for HX711 from and start...
Hello,
It would be nice if the HVN tx complete event structure had the attribute handle of the characteristic that was just notified. This is already done for writes and...
Hey guys,
I'm working with the Laird DVK-BL652 and the Nordic SDK v.14.2.0 with Eclipse (Kepler) and try the example "SPI Master". I didn't modify this example but after...
Test Setup:
SD 6.1.0
SDK 15.2.0
Peripheral: nRF52840
Central: iOS 13.1
Central is connected to two peripherals, each peripheral is sending 50 pkt/s, each packet...
Hi,
We have a nrf51822 based custom board with no button, we use accelerometer tap detection to wake up the system. Currently there is no software protection for the battery...
After getting my nRF9160DK activated and showing up in the NRFCloud it would just sit there blinking led3.
I deleted the device from the cloud and tried to update modem...
i create device information service BLE_UUID_DEVICE_INFORMATION_SERVICE,and Bonding on the phone.
i want to update the PNP_ID_VENDOR_ID and PNP_ID_PRODUCT_ID，
method 1...
Hi,
I'm using NRF52832 DK to integrate the LittlevGL graphic drivers . I'm facing some problem while integrating the sdk's.
I'm getting the errors:
.\_build\nrf52832_xxaa...
I have found what I believe to be a bug with the nrfx_qspi driver on NRF52840. After using the QPSI peripheral, I have found that in some cases the NVIC's IRQ#41 (QSPI Interrupt...
