Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear all,
I am trying to adopt the flash_fds example to fit my needs. What I initially need to get sorted out is how can I erase the memory pages after I have fully written...
hi, team.
I've got a question. I use nrf52840 dev board. There is a connection between nrf52840 and ds18b20. I tried to use dedicated HW timer to count delay according to...
Hi team,
There is connection between nrf52840 and ds18b20. I have made simple lib for ds18b20. When i get temerature without softdevice (s140) all works correct (use 9-bit...
Howdy,
I'm trying to access the SD card on my device via the usb MSC and am not sure the best way to proceed.
I have a custom board with an nrf52840, and it works great...
Hi,
I would like to make development on nRF52840-DK by using Segger Studio.
However, I could not find detailed document that specifies how I should start development...
Hello all
I was just following the thread launched by Alex concerning nrf 52 dongle driven from serial port, which is also very important to me, and now that thread is already...
Hi,
i would like to program my module nRF52840 via uart.
I generated private then public key using nrfutil.exe tool
i could programm softdevice and bootloader and...
I am trying to get the DCDC running on my custom NRF51822 board.
It is running but the results are a bit disappointing.
If I do a test and enable the TX with and without...
I've picked up a nRF52840 DK and dongle to do some testing with long-range beacons.
So far I think I have managed to configure my DK as a beacon in long-range mode (can...
Hi
I have a test mesh network, with several devices provisioned using nRF Mesh and.... a proxy node which has been provisioned using an alternative method but with the same...
Hi, I'm trying to make a SIG qualification Project. QDID97989 (nRF52 S132 V5.0.0) with replace PHY QDID97482(TaiyoYuden module). Launch Studio Project type is "qualification...
How to send and receive messages in ble mesh? The sending and receiving of sensor data I have done is not a switch value. I have tried many methods but failed.
I alredy run the assert tracking about 4 months ago on preliminary firmware.
Now I updated the modem firmware to v1.0.0 and compiled the last stable AT Client project from...
In the past we had a C based product that communicated from our Host processor over SPI to an nrf8001 peripheral using an Application Controller Interface (ACI) provided as...
