Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello, I have just started using nRF52840 DK and previously I have used development kits from different vendors so, I was wondering when developing which resources are available...
Hi All
I know this is stupid but I can't figure it out - either I've missed something obvious or not connected something properly (or at all).
Using the PCA10040 nRF5...
I have developed a custom board with NRF52810 (Rigado), a standalone CAN controller (500 kbaud) and serial communication (57600 baud).
The SW is based on the BLE_APP_UART...
Can anyone tell all the potential reasons for stack corruption? I'm debuging a problem where sometimes there is no stack trace when putting a breakpoint on the first line...
I have a project based on SDK 15.3
I've set #define NRF_LOG_DEFERRED 1
The project generates a high volume of log output over RTT
NRF_LOG_FLOAT_MARKER is a macro that...
Hi, I am using the nRF51822 with SDK 12.3.0
I am trying to make use of nrf_drv_spis driver included in the SDK.
My purpose is to have nRF51822 constantly be RX-ing over...
While investigating my stack corruption issue , I noticed that the RADIO_IRQHandler is always called twice in quick succession:
But the NRF_RADIO->INTENSET register only...
I'm trying to communicate between two devices (nrf52840 and teensy 3.6) over RS485, but I'm having some issues using the UART library in the SDK. I'm trying to create an interrupt...
Hi,
It all happened today after being used the board for a month. when I tried to turn on the board it does not blink LED5 nor does it show up in the device manager. I to...
Hello Nordic,
I have multiple Thingy52 devices upgraded to V2.2 firmware via nRF Connect application on my android phone.
Have been trying to add the BL Mesh light switch...
I want to read timestamp in my nRF9160 device and found that "z_tsc_read()" function in Zephyr RTOS will do that. However, I am not able to include the main library of the...
Hi,
We are developing mesh control lighting system with nrf52832, now we're able to control devices through mesh.
But now we're having problem with showing node state...
Hello,
I have two devices, one central and one peripheral and I try to implement whitelist. I took a look at ble_app_hrs_c example and the whiltelist is working on central...
Hello,
I am using ble_app_blinky. I have a basic query about event handles. There are lot of event handlers registers as part of initialization. Will all these event handlers...
Hi all, we has experienced two PPK boards start to give faulty reading after several uses. I attached two screenshots about current reading with same setting on the DEV board...
