Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
In https://devzone.nordicsemi.com/f/nordic-q-a/47707/how-to-use-sd_rand_application_vector_get-correctly, you suggest to wait a couple of milliseconds if I run into NRF_ERROR_SOC_RAND_NOT_ENOUGH_VALUE...
Hellow everyone, I'm testing the UART communication between the MCU and the PC. There is communication in both directions, the problem is that even if you only press the keyboard...
I was hoping to get an explanation of how the LTE Sensor Gateway sample app works. The SDK documents the sample app here: https://developer.nordicsemi.com/nRF_Connect_SDK...
I am using SPI to transfer data between an ADC and my NRF52 (the spi master) on a custom made pcb device. I call the SPI data transfer in a BLE_UART example (from the SDK...
Hello.
I have encountered a case where app_timer gets stuck indefinitely while processing its timer queue. I have attached a simplified version of the code that runs on...
Hello Nordic Team,
I have an application running on SDK 13.0 which uses the app_timer for some timeout handling and so does repeatedly call app_timer_start and app_timer_stop...
Hi, had to modify this file
SDK nRF5_SDK_15.3.0_59ac345 in file apply_old_config.h
line 818
(SPI_ENABLED && (NRFX_SPIM0_ENABLED || NRFX_SPIM1_ENABLED || NRFX_SPIM2_ENABLED...
I've been learning to use the PWM.
This should set the PWM up for a period of around 250ms
After the period is over I expect to clear pin 23.
I find that its cleared...
Hi All,
In nRF52 SDK 15.3.0 , example ble_app_uart in peripheral mode, i have changed the TX characteristics which is initially of type (notify) to type (read ). I am able...
Hi community, I have a problem establishing a connection with more than one device in the MQTT client example (MQTT/6LoWPAN/BLE). I'm using:
SDK v15.3.0 (also nRF5 SDK...
Hi,
I'm trying to connect my nRF52840 SoC to nRFgo Studio on my Windows 7 Laptop using the usb connection on the nRF52840, unable to see any data about the connected board...
Hello everyone,
I need transfer large data 12KB array send central to peripheral using nrf52832. I try this examples in central (ble_app_uart_c) and peripheral (ble_app_uart...
Hi,
I am using nrf52840 with custom board, sdk 15 and and softdevice 6.0.0. I modified saadc example to sample SAADC value once and stop it in saadc_callback. Everything...
I would like to know, what is the correct workflow with Alarms ZCL cluster?
There are no examples with it in SDK (at least, as I have seen). The documentation on this subject...
