I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
We have a firmware application using SDK 12.3 and Softdevice S132 V3.0.0 running on a nRF52 controller.The firmware is used pheriperial BLE device and provides a GATT...
I am working on ble_app_hids_keyboard example code. I downloaded the bin file in my eval kit and tried to connect the Nordic_keyboard device with my android device. Then,...
Looking at the "Pin assignments" section in nRF52840, I found that some GPIO pins are recommended for standard drive, low frequency I/O only. I am wondering whether there...
-SDK: 15.0
-S132
-nRF52832
-Segger studio
I'm trying to implement bonding/whitelisting to my project, which is a connectable beacon with a custom service. What I want...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant " examples\peripheral\pwm_library " to " examples...
I need to change, on a time basis, the advertising packet :
Let's say for X seconds it has to work as a "iBeacon"
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello,
We want to build Expiremental examples in BLE Peripheral.The Common issue which we have faced in bulding any of the Expiremental BLE Peripheral issue was the missing...
Hello. I am using the custom board (buttonless) of nRF 52840 to verify the services of DFU and NUS. After firmware rewriting with DFU, I confirmed that BLE communication with...
Hi,
Our Application software running in Micro is communicating with BLE over UART.
So in nutshell, we are using serialization to speak with soft device present on NRF52810...
Hi,
I'd like to have a second UART available, as the nRF51822 only has one and I'm wondering if there exists a UART software emulation example implemented already for this...
Hi!
I'm trying to add logging modules to my own libraries that I've created. I'm using SDK 14.3 with the nrf52832. I can enable logging for any of the SDK driver/libraries...
I am using nRF Connect to measure the power of the nRF52840 DK. But I don't know how to output the raw data out. Is there a way that we could get the data out from nRF connect...
We are evaluating to use this IC for BLE/NFC purpose.
we would like to flash the nRF52840 thru our Linux processor (not using external flashers), using the SWD lines connected...
