Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi Every one,
I am trying to use two uart's communications concurrently in nrf51422, in my code i am running timer of one second.
Every one second in timer routine trying...
hi....
i am using nrf52382 and segger 15.2 version , i want my peripheral to send the data only if it reaches the certain limit (threshold value) on that case it should...
hello , friends
i am using nrf52832 ,debugged the ble uart program ,and then i tried to connect my device over ble uart app,i couldn't found my device ,then i tried to connect...
Good morning!
First of all, the background. I made a custom board and programmed it, everything worked like a charm. After that, I made another one, same hardware, same...
In my previous question , where I wanted to atomically send a large bulk of data, the solution was to keep track of p_bus-> free_buffers , in order to calculate the amount...
Hi,
I’m using SDK 15.00 and I have some issues with NFC. When I’m trying to connect with NFC - NFC_T2T_EVENT_FIELD_ON event occurs. At this point, I need to start BLE...
The release notes for S132 v6.1.1 lists a bug fix:
"Fixed an issue where NRF_TIMER0 may not be reset at the start of a radio timeslot (DRGN-10650)."
Did this bug exist...
Hi,
Here and here are examples of a port of the nice u8glib library to stm32. Based on these, i tried a port to nrf52, but was not successful so far.
I call the oled...
I am trying to save data to the flash memory. My starting file is the ble_app_uart_pca10040 (s132). I am using the sd_flash_write address is 0x007ffd0 and a value of 0; I...
We have developed a custom board using Raytac MDBT50Q with NRF52840. It has an external EEPROM and a RTC. We made an app that we use to program 4 daily alarms through BLE...
nRF51822-EK page is no longer available on the website. By any change I can get the PCA10001 schematic somewhere?
I would like to run some conductive RF testing and would...
Hi,
I recently moved a project from Mesh SDK v2.2.0 over to v3.1.0. I read the release notes and saw that there have been some changes to the Flash Manager module.
During...
I need to include in my project Advertising, buttons and battery power measurement.
I am using SDK 15.2
If I get ble_apps_bps and include advertising functionality (from...
