Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
When static authentication is used, it is my understanding that both the provisioner and the privisionee have a static preprogrammed key. The SDK says:
"The application...
Hi, starting from the demos on the devboard, I want to make a custom pcb work now. For that, I do not need UART/logging functions, which will otherwise cost me current consumption...
I use SDK15 and S132. I have examples\dfu\secure_bootloader\pca10040_ble loaded in my board. I can see it advertising when there is not valid app loaded.
Also, my app with...
Hello Nordic Team
I am working on zigBee project. I see there is uart example available in SDK which works BLE + end point. Is there any example available which works on...
Hi all!
I found solution for Xiaomi zigbee smart home sensors (gerkon, water sensor, pir motion, and other...) based on CC2530 zigbee shepherd and Trust Center Link Key...
I am doing a project with nRF24L01+ but i found out this is not certified chip to FCC. Is any other RF that is certified that i can replaced this RF24?
Hello,
I am creating a read-only characteristic with sd_ble_gatts_characteristic_add (specifically, characteristic_add). The value is 31 bytes.
On a Read Request, it is...
Hello
I would like to send my sensor data to a mobile application using BLE SDK 15. Someone suggested me to go through the BLE NUS SERVICE example which was a good one....
Hi,
I am new to Nordic development environment.
I am compiling the some code developed by vendor for NRF5 SDK 12.2.0
I am getting errors such as
Error1 snippet
...
Dear Colleagues,
I could use some help or ideas. I’m working on the link layer encryption of an open source Bluetooth stack. It starts to work! But, now I have the effect...
Using softdevice 6.1.0 and SDK 15.2:
Is it safe to use NRF_UICR->CUSTOMER[0] through CUSTOMER[5] for storing serial numbers?
It seems through in previous versions of SDK...
Hi All,
I have implemented the code for MASTER serial DFU in ST micro controller. which can send the app .bin file. I'm using 57600 baud and disable the flow control....
Hello,
I am using 15.2.0 SDK and 3.1.0 Mesh SDK.
I was trying to control two LED's on the nRF52DK using two generic level server models. I made following changes to the...
Hello. I got an nRF9160 DK with an iBasis eSIM that was already registered on an nRF Cloud account. Is it possible move the already activated eSIM to my Cloud account? I tried...
