Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
i am using the Visualgdb with sdk v 13.01. i have Nrf52840
i was trying to read the DeviceID of ADXL345
i am using API from this thread
devzone.nordicsemi...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
What I have to do if I met this ? I round length to fit (len+4-(len % 4)). Is it right ?
if (!(IS_WORD_SIZED(m_start_packet.sd_image_size) &&
IS_WORD_SIZED(m_start_packet...
Hello,
We have problem BLE connecting to the nRF52832, if we use the method gap_init(), the "better" smartphones can connect(those who support BT 4.2). If we skip the gatt_init...
Hi,
I'm trying to program an external NRF52832 board with the NRF52-DK, per the instructions in this post .
Programming works fine, but the code doesn't execute after...
Hi,
I'm trying to do DFU in my app, I almost complete it, I met a problem that my app flashed back when I sent 04 to the device.According to the DFU doc,after uploading firmware...
Hi,
I'm using the ADC of nRF52832 on nRF5 SDK V12.2. The setting as attachment. I found that it just do sample one time. But I have use timer to call nrf_drv_saadc_sample...
The scenario like this:
A is BLE peripheral with firmware (ble_app_uart under nRF_SDK_13.0.0_04a0bfd), if no filter,any central can cenncet to it, but I just want B can cennect...
Dear all,
Help please,
I'm evaluating ble_app_uart (Central/Peripheral) but I don't understand how to disable the echo I have on the RTT USB VCP
When I send data from...
I am using 3 nrf52 DKs with S132 and SDK13 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and added the relevant...
Hello! I try to use three modules with chip nRF24L01 to syncronize two slave devices by one master device without wires. Required accuracy is about 10 nanoseconds. My idea...
