I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi,
I have a nordic chip (nrf2832) and I am trying to use it as a LWM2M client and register it to a LWM2M Server. I want to achieve this:
developer.nordicsemi.com/.....
I'm trying to update my SoftDevice with a bootloader, which is basically the same as the one in nRF5_SDK_11.0.0_89a8197. The image is saved in bank 0 and is validated by dfu_sd_image_validate...
This is my first DFU project, and so this may be super-obvious to all of you.
I am writing this here to help others, because it appears that there are others out there...
I have an mBed application that uses the S130 SoftDevice and polls data from a couple of other connected peripherals via I2C & SPI.
I use a Ticker object, which seems to...
Hello,
I use the example dfu_dual_bank_ble_132 in the nrf5x sdk 11 (PCA10040).
I have had my programe before the OTA, i will have a programme wich would update at any...
Hi all:
I stored some settings in flash in the address 0x00077000 and this address is got by the function of pstorage_register().
However this area will be erased by...
Hello there,
I've been trying to use embitz (the new version of emblocks) to program a nRF5188 but i always fail to compile the "ble_peripheral_hrs" exemple, i'm always...
Hi
I have a unit that is rather old and I want o update it to the latest softdevice.
In the unit there is a bootloader and softdevice version 6. Does anybody know if it...
I'm making progress, but still struggling to get the sample DFU built into NRF Toolbox to download successfully with my bootloader. Using hrs_dfu_s130_*.zip.
For this,...
I tried if there is a possibility that my device would brick if I interrupt the DFU process. notice that I'm using SDK10 with dual bank bootloader. I uploaded the app over...
I am going to develop on nrf51822 and the data sheet says nrf51822 is s110.
I want to load an example of sdk 11 but there is no example for s110.
I am a total newbie, so...
On the nRF52, does the TASKS_HFCLKSTART need to be trigger again after waking up from sleep, if the the HFXO was started before going to sleep? Or does the Clock control circuitry...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I have one characteristic which send data with indications, for each frame sent I wait for acknowledgement on case BLE_GATTS_EVT_HVC : before sending the next data
but...
I write a source code to test led and button driver. it's work with a loop but when add sd_app_evt_wait() to use low power mode of nRF52.
I suppose that I forgot something...
