Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
I am trying to implement the ANT+ Environment Profile using the nRF51 DK and I was wondering if anyone had done this and could point me in the right direction to start. I...
how to synchronize multiple NRF52 them?
Should I use a router? What route do you recommend for development?
Otherwise many people tell me that the Bluetooth has a very...
Hi all,
I create 4 timer in APP, and there seem only one timer (work in single shot mode) can not trigger by right ticks.
I add some log and find that:
First I...
Noticed in ant_parameters.h
#define MAX_ANT_CHANNELS ((uint8_t)15)
First question: is this correct for nRF51?
Second question: is nRF51 going to support 15 channels...
Sorry for the newbie question -- I am new to programming microcontrollers.
I would like to know if it is possible to program the nRF24LU1+ to behave like a USB host? I...
Hi!
Is this correct scenario to minimize battery usage for radio tag transmitting 8 byte packets at 3 Hz?:
setup:
turn LFCLKSRC on with CLOCK_LFCLKSRC_SRC_Xtal...
Hi all, i am trying to start using the smart beacon kit nRF51822, but searching around i am a bit confused on how to flash the most recent softdevice with sdk on it; i followed...
I'd like to do the same thing :
how to use dm_device_delete
nRF51822 S110 v8.0.0
nRF51 SDK v10.0.0
DEVICE_MANAGER_MAX_BONDS=2
I test Nexus5, Nexus7, iPad...
I want to read and write RAM (target=nRF51822) from a custom C application while the CPU is running.
Now, I can do this using the nrfjprog.dll and I get the expected values...
Hey guys,
I'm working with a nordic nrf5182 and s130. What I need is to put the system in sleep mode after a reset. The main problem is with function sd_power_system_off...
hi,I have to question about ADC,please help me ,thank you very much!
I joined on the ADC input pin an adjustable resistance, to change the voltage value.Why change the...
Dear Sir:
I have designed my board with nRF24LU1+, and I want to debug it through ULINK2 JTAG.
However, it seems not working.
Would you please share me with some ideas...
