Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, I use Gzll protocol to realize 2.4G frequency hopping communication, Two Device send data to One Host on Pipe1 and Pipe2.
1 Two Devices occur "loss power" many times...
Hi,
I'm working on custom PCB and I have small issue.
After making PCB I was trying to connect, but no luck - "(unable to connect to the target)"
Maybe there is something...
As try to let keil's project into eclipse
so i edit makefile from example
first i open project by keil to copy include paths and paste to makefile under ''#includes common...
Sorry for the amateur question. I'm an iOS developer and trying to replicate the functionality in the nRF51 sample app: github.com/.../IOS-nRF-Toolbox . I understand the code...
Hi
We develop an application on nRF51822 the with GCC C++ and try to include the file ble.h in a .cpp file.
As soon when I include the file in the .cpp file I get compiling...
HI,ALL,
i find such sentence in core
(BLUETOOTH SPECIFICATION Version 4.2 [Vol 1, Part A] page 13)
'A Controller is a logical entity defined as all of the layers below...
reference nRF51-ble-peripheral-bond-handling example pairing/bonding mode. I add device manager & app_bond function on ble_app_uart. why function handling on "app_bond_init...
I want to make a rtc calendar.As rtc1 compare channel 0 had been used by app_timer,so I use rtc1 compare channel 1 to generate interrupt very second. But the channel 1 didn...
Hi,
I've just discovered that there are counterfeit copy of nrf24l01
Are there also copies of nRF24LE1, NRF24LU1 or NRF51822 ?
Is there a guide to recognize genuine Nordic...
Hello,
On S130 conn handles were 0 to 2 for connections as central and 3 for connection as device.
I migrated to S132. Question, when i set 3 / 1 as configuration, do...
Hi, I've added micro ESB to work during BLE timeslots granted, with uesb_config as start of slot and uesb_disable as end
During the slot, the regular work, uesb_event_handler...
Hello, Nordic stuff.
I've been working at S110 firmware and coming into a problem of service discovery from a central device(iPhone).
I'm using S110(v6.0), Keil(V4.73...
On pca10028 dfu_dual_bank_ble_s110_pca10028 example works fine. First i programmed soft device s110 and then dfu dual bank example my board gets into dfu mode and i can upload...
Hi,
I'm trying to get the UART working, following the idea given in the Nordic Infocenter / nRF5 SDK Hardware Drivers / UART / Using the UART Driver.
I have downloaded...
The code below is transmitting data from device (mcu+BLE) to an open source BLE terminal :
void BLE_communication_device_to_app(void)
{
ble.updateCharacteristicValue...