Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I am using the PPK2 to evaluate the nRF5340. Neither of these devices is currently working properly, I think the underlying cause has something to do with USB that's...
Hello, I am using SES ARM V7.32 and SDK is 17.1.0.
I am trying to test the ble_app_uart example, but Build failed keeps occurring.
There are no other error comments, so...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hello All,
I am using the nRF54L15-DK and the nRF Connect SDK v2.8.0 with the Zigbee-Addon.
Is the maximum TxPower value that can be set for Zigbee 8 dBm?
Best regards...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The action was executed, and the date and time are...
Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
Hello,
I have a custom board which has an nrf5340 on it. We are using nRF Connect/Zephyr in this project. Currently the board has a pretty simple interface seen in my overlay...
I am currently developing a PC application for Bluetooth data reception and chart display. I want to perform secondary development on pc-nrfconnect-ble. My current development...
I'm using SDK15.3 on an nRF52840 with FreeRTOS and specifically non-preemptive scheduling.
I want to so some transfers on SPIM (it's configure with DMA but that's not a...
My project uses a PDM microphone connected to a nrf5340. I previousy had this working using the nrfx_pdm driver, with NCS 2.6 but then had to migrate the project to NCS 2...
There is usually a panel for application where you can see / delete or add build configurations, as shown in the enclosed picture. The panel on my vs code installation has...
Hello,
i am debugging issue in our device. I ported the nrf5340 Audio application to our custom board and modified it for our use. We use audio broadcast mode.
Device...
HI,
I am developing a ble mesh application on SDK 17.2, I enable Instaburst for support long mesh message(more than 300 byte), it worked well.
Now I changed to the nRF...
Dear Support Team,
I'm trying to develop a mouse using Pixart's PAW3395 sensor. I've written functions for reading and writing data through the SPI interface. I took help...
