I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I use vs code to run nRF9160 DK applications and it runs fine for a month. But recently I cannot build configuration even in an empty application . Old good applications...
Hello,
We have an nrf5340 custom board and during frequent BLE connections/disconnections sometimes it seems the netcore gets stuck. We are connecting to an iOS app and...
Hi:
Pls help me!
I use ncs v2.6.1.
C:\ncs\v2.6.1\zephyr\include\zephyr\sys\util_internal.h
When I check #define Z_IS_EMPTY_ (...) No matter what I input, I can't get...
Hello Nordic team and community,
I’m exploring the possibility of creating a mobile application (potentially using Flutter or native frameworks) that would act as a Distributor...
Hi,
I'm facing a critical issue with our sensor's power setup and would really appreciate any insights or suggestions.
Our sensor is currently using a CR2477 battery,...
Hi guys,
simple question based on your experience: what is a realistic data rate between an Android device and an nrf52805 with S112 on board?
I tried a lot of tweaks...
Hi, in our project we use the nRF52832 and a external flash memory MX25L3206E connected on this pins:
Take note in this project we also use SPIM0 to manage an IMU and...
Hi, I just purchased new PPK2 kit from mouser.
But after trying to open it via nrf Dekstop app it gives and error
2024-11-19T11:57:53.845Z INFO Selecting device with the...
Hello, I am trying to achieve a few uA current in nrf9160 but with even all conf off and empty while loop or even without the while loop the controller is consuming 5mA which...
We are currently working on a project based on nrf52840 and using connect sdk v17.0.0.
It is currently in development phase but eventually we are planning to use nrf5340...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
