Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi
For a specific project i will need to have ability to monitor some 4G/3g/2G protocol stack L2/L3 messages. Is it possible? is there any documentation regarding this option...
Hello DevZone,
In NCS, we have many BLE Mesh examples that is initialed by:
The first argument is a structure that contains some input and output OOB callback functions...
Hello,
Currently I am implementing the nrfx qdec driver in our Zephyr project using the nRF52840 DK. We choose the nrfx driver as this provides events. I am using the nRF...
Hi.
I have designed a node with NRF52833 with +8db power antenna.But i got some issue in signal transmission over 1km range.Please review my layout and matching circuit...
I have the software installed and I am using the nRF52840DK with Ubuntu 22.04. The uart link is /dev/ttyACM0
When I start wireshark and do a capture on all advertising channels...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
