I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
Hello,
Is there examples of paring,bonding and whitelisting?
The pairing and bonding mode is static password.
It is best to have examples of the central and the peripheral...
Hi Nodic support team.
I am using esb_ptx and esb_prx for testing interface.
Can i change nrf_esb_payload_t.data in receiver of esb_prx?
It is always 8 bytes even though...
Hello everyone,
I followed the guide from this site to connect an Adafruit PN532 to an NRF52840
and tried running the adafruit_tag_reader example from the SDK.
However...
I implemented firmware update over LTE Cat-M and Ethernet last year by modifying the `fota_download` and the `download_client` examples into my own slightly modified version...
Hi,
I am using nRF52833-DK connected to my PC with usb cable for programming and debugging using the on board jtag.
In the beginning all worked ok, suddenly the jtag stopped...
Hi，
I have a custom board with nRF52833 and sky85303-21 FEM. To control the FEM, I have added the following code to my app.overlay file and enabled simple GPIO configs....
Hi everyone,
I'm encountering difficulties running my application on a custom nRF52840 board with a 48-pin package using Zephyr NCS version 2. 4. 4 in VS Code.
The problem...
Hi
Iam trying to make an ble advertiser project on nrf52840 with nrf21540(custom board)
there are a few configuration changes required for the board(pins and supply voltage...
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Earlier I was using nRFconnect SDK 2.1.2. Everything works perfectly fine with that. Many features were added in that project. Now I want to port my project to latest SDK...
Hi Everyone
I'm developing a project using NRF52840 , the application needs OTA over BLE . It was working before without no issue , we tested in many devices and many times...
Hi,
I'm wondering if I'm missing something. I've been creating a bluetooth mesh light with hue, saturation, brightness, on/off, etc. models. However, my model_handler.c...
I have an app that uses the Nordic IOS-DFU-LIBRARY to drive the OTA DFU process with an Adafruit nrf52840 Feather running the Adafruit bootloader. I have the library setup...
