Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I have developed a custom board using nrf52840 IC and I need to use UART. For this I have two pins available P0.19 and P0.20 to be configured as RX and TX. I checked those...
I am using a BC840 on custom PCB for a low power data logging application and am struggling to get lower than 270uA sleep current. This part has the 32mHz external crystal...
Hi,
The python nrfutil package doesn't seem to be actively maintained.
Latest updates don't support python version > 3.9 which are now default versions for latest Linux...
Hi,
I downloaded the project for PCA10040 with HID Mouse in ...\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs . From Iphone and computer, I could...
Hello,
in my project i want to use watch dog timer in ble_app_uart_pca10040_s132 but am getting error as shown in image1, even after including driver files and paths
...
hello,
I'm trying to use RSSI Viewer for my custom board - problem is I need to change UART pin.
How do I make my own FW/binary for RSSI viewer?
My custom board uses...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
I'm testing with the new rev of the nRF52832 (build code QFAAGB on the package), and I'm not able to observe behavior that makes sense to me per the updated product spec....
