Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello: I am trying to design a project about a type of sensor powered by high accuracy battery which is using the nRF52832 chip in a custom board. To use the battery energy...
Hi
My requirement is to upgrade the application firmware on the nRF52840-DK from another processor using SPI interface, and I am trying to understand the code to plug-in...
I'm developing a beacon application using the Fanstel BT832AF, which uses the nRF52810 internally. This unit is mounted to a custom board, but before raising a private ticket...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
Hi Nordic team
Customer SecuX failed to use JLINK V9 to update modem firmware to Thingy91 and customer nRF91 board both.
But, JLINK V9 can program merged.hex file(application...
I want to bring up a secure bootloader with support for ECDSA and SHA-256.
I am having a hard time coming up with a combination of SDK components (frontend, backend), external...
Hi All
I'd like to implement "Fast advertising" with SDK14.10
Q1: I add some code in advertising_data_set() to do fast advertising, is that correct ?
Q2: If want...
Good afternoon. I have the Zephyr gsm_modem sample up and running for my GSM modem and a PPP connection is established to the cellular network. The example does nothing further...
After I write bonding data to flash memory (SoftDevice has been disabled before the write) I get an APP_ERROR:ERROR:FATAL. But I do not know what is causing it. I do an NRF_LOG_DEBUG...
Hi,
We added new commands for code from openthread and generated .hex file by "make -f examples/Makefile-nrf52811 NCP_SPI=1 FULL_LOGS=1 && arm-none-eabi-objcopy -O ihex...
We are planning to develop BLE and Bluetooth Mesh products using nRF52840. I have a couple of questions in use of Zephyr. 1) What is advantage of building BLE or Mesh on Zephyr...
Hi,
I tried to build the ble_app_uart example for nRF52820/s140. In my project I need to use C++ modules.
My usual approach that worked so far:
Take an example project...
Dear Nordic Semiconductor-Team and everyone else, thank you for helping the thousands of people in this forum an answering their questions thoroughly. I have a question/problem...
