Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hello to everyone.
I'm working with chip nRF52832 (PCA10040) and Mesh 3.1. I'm trying to connect a HC-05 Bluetooth/Serial Module using its serial pins (Rx/Tx) to the default...
Hi,
I am using SDK 15.3 and NRF52840 Preview DK
I have a requirement where I have to glow one of 3 LEDs R-G-B (each connected to one gpio pin) for 1 second and turn...
I'm using nrf52840 to develop a remote control using BLE long range.
We use two nrf52840 : on inside the remote and another in the system to control. The remote is used...
Hi,
I've done a lot of searching and Googling and could not find a proper answer for the life of me, so I'm posting again here to try to find answers. I must have looked...
I want to use internal temperature sensor in the example, "peripheral\temperature" on our software but there is the problem that we met when applying on board internal temperature...
I'm using nRF51DK and created 2 app_timers (based on LFCLK) that are running on 32.768kHz crystal, one for kernel timing (10ms) and one for real time clock (every second)...
Hi,
For some reasons, I would like to write my own application for updating the firmware, something like NRFUTIL application.
I wrote it and everything is working fine...
Hello,
I am trying the ble_app_cts_c_pca10040_s132 (current time service client). Under the conditions described below, ultimately a SoftDevice call to sd_ble_gap_device_identities_set...
I am attempting to integrate examples/peripheral/flash_fstorage into my project (SDK 14.1.0).
When calling nrf_fstorage_write I get NRF_ERROR_INVALID_LENGTH in response...
I am trying to provision 2 clients for the mesh so that i they all can send the message to a single server.
I will list what all i have tried
1.I took a server node and...
Our custom board uses internal RC clock source and I tried to build original sample app, "ble_app_pwr_profiling" in SDK 15.3.0 using attached sdk_config.h modified only with...
I downloaded the latest nRF5_SDK_15.3.0_59ac345 and some other old versions of SDK documents. (I am trying to use pca10040 development kit to program Fanstel EV-BT840F, aka...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
