I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
hi,
I am compiling nrf52840 light switch sample code in an embedded studio, I am getting the error as extern "C" {: Invalid argument, how to get out of this
I just began working with the NRF52, using the SparkFun breakout board. I'm developing in Segger Embedded Studio. I am aware that there are drivers for this chip in the SDK...
Describe the bug We have been buying nRF5280 boards and flashing them from open thread website in the first couple tests the devices work properly and connect to each other...
I use SDK15, nrf52832, s132
When in the
I comment
two lines.
Seems works. I can observe on an android nrf connect my device. But on a IOS can't see it via standart...
I am developing the product using nRF52810-CAAA. I have initialized it for SPI use as follows.
This will increase the current consumption by 3mA. Why? Is this normal...
Project configuration: nRF52832, SDK 12.1, s132
We have a system with ESB, BLE and FStorage for NV access. The system works great with either the ESB and FStorage, or, BLE...
Hello,
We are evaluating the nRF5_SDK_v15.0.0 example OTA DFU bootloaders on a nRF52840-PDK. We have generated a signed firmware update package using nrfutil pkg generate...
