I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Can anybody help me to get out of this error, Error programming through Seggar Embedded Studio,
Additional Load File[0] "E:/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96...
Hello.
I try to make audio noise meter on nRF52832. I used analog MEMS MIC with OPA which I turn on via MOSFET while before measurement. I'm using SAADC triggering by RTC...
Hi there,
What changes should I have to do to the light switch example to provisioning the client and server using group address instead of unicast address?
I believe...
In our application we need to have the NFC pins configured for GPIO and APPROTECT enabled.
As an additional safety feature I verify the UICR content inside my application...
Or any general how-to documents when the users want to set up any peripheral using the direct register access? I try not to use SDK for simplify and minimize the code side...
Hello,
I'm trying to implement the Gazell protocol for one of my tasks. I understand there is CRC for the data sent from the device to the host. I cannot however find anywhere...
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
Hello,
Is there any development board like an Arduino mini for the nrF52840. It need to fit a in very small enclosure
Ideally, I would like to test/develop some sensors...
Hi,
I am working with hid keyboard example on my Windows machine.
Problem 1 : After flashing the code, I make bluetooth connection and the code works properly. Then I...
Hi,
I am reading the Product Specification v1.3 of the nRF52832 SoC.
On page 23 the RAM0 block section 1 address is given as 0x21001000.
From the context I believe, this...
As per one of my discussions with , on another thread here , I can send a GenericOnOffGet from my android activity and I will get the status of the light in GenericOnOffStatus...
Again!!! I have a lot of problems to navigate on the Nordic products.
I follow the links and went to the start52840dongle and downloaded the SDK.
I find only stuff regarding...
