Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have recently begun running into issues related to the SPIS module on my nRF51822 S100 v7.1. Fairly often, between 10 and 20% of the time, the interrupt does not fire when...
Hi,
I am using TIMER2, GPIOTE and PPI to implement a 6250Hz square wave at a GPIO pin. I can successfully create the square wave on the GPIO pin. However, I would like...
Hi,
I want to use nrf51822 for implementing HID keyboard and mouse.
Can the application be configured for keyboard and mouse simultaneously ?
i.e hids_init_obj.is_kb...
Hi,
I am using nRF51822 and trying to use Ticker from mBed library.
I have issues when using Ticker and PwmOut.
How is implemented the Ticker functionnality into nRF51822...
Hi,
I want to make a pulse for buzzer and led.
I find a sample source(led.c) and the Nordic SDK.
It is good enough in case posivie and negative duty is same.
I need...
Hello ,
As mentioned in another question, I would like to use the nrf51822 SPI slave peripheral to benefit from the DMA capability although I want to behave as an SPI master...
I can't seem to find where/how the BLE address gets randomized so it changes periodically when using the BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE address type.
-It seems...
Are the OVERRIDE parameters useful in any way shape or form when using the NRF_2MBIT mode?
Is there any reason other than BLE compliance to use the OVERRIDE parameters...
I cannot uninstall MCP on my W7 x64 system using the normal control panel add/remove programs method. It appears that I need to re-run the original installer which I no longer...
Hej,
that might sound like a dumb question, but what is the minimal setup to program an nRF51822 SoC using the SWDIO/CLK ports?
What external hardware is required...
As nRF51-DK User Guide said: "If you have swapped to the mbed image and want to revert back to the J-Link image, download the latest SEGGER J-Link software from www.segger...
I have bought the Beacon Kit because it matches my needs in terms of PCB shape and size, I have Evaluation Kit as well and use it for debugging purposes, but would like to...
I want to know the time range of advertise timeout.
Why it doesn't work if I set the time to 360 seconds?
It can work if the time less than 180 seconds.
Is the range 0...
Hello,
I would like to develop an application that makes photos using a small camera from the omnivsion series and send the data via Bluetooht, using the nRF51822. These...
