I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
Hi,
I encountered some problems when using UARTE.
In terms of hardware, I have connected the 52840DK LOOPBACK_PIN_1A and LOOPBACK_PIN_1B.
Software code is the original...
Hello,
I see that kiss_fft is used in the libLC3 library. I would like to use it for another part of my product in addition to the pre-compiled LC3 lib, but don't want to...
I'm pretty new to embedded development/electronics and I'm trying to interface with a I2C pressure sensor, but I can't seem to communicate with it. I'm using nrf52840dk board...
Hello,
Up until today I had been developing fine with visual studio code, installed via Toolchain Manager. Then, I clicked "Pristine Build" for the first time in a few days...
I installed the VSCode extension for nrf connect.
I want to do the build on this page:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/thread/tools.html...
Hello Team,
example: SPI master_slave advanced non -blocking
i just open nRF connect sdk example in vs code and build it
I am getting below error while build
Please...
Hello,
I am trying to play with zephyr networking samples on my nRF5340 + nRF7002 EK devkit board.
I am using NCS 2.7.0 release SDK. i was able to build and run some Wi...
I'm not sure if zephyr questions can be also asked here. Problem I am struggling with is approtect mechanism to prevent flash readout. I am trying to use Zephyr config files...
Hi,
I am currently developing a custom Zigbee end device with support for FOTA updates. My FOTA seems to work (all data gets transferred correctly) but the update won't...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello,
I am uploading my code with a basic URI to be advertised by the chip.
I am able to build and upload the code for the nrf52832 in my nrf52 DK, the program works...
