Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Trying to use the QuickStart for the Laird Pinnacle DVK. The Quickstart only shows that JLink is detected, but not supported when connected. Even connecting directly to the...
Hi,
I want to get the tick count of the system with sys_clock_tick_get(). I am using a library for NFC reader chip ST25R3916B and provided library from STM requires a platform...
Hi,
I am using https://github.com/NordicDeveloperAcademy/nRF-Connect-SDK-Fundamentals lesson5/fund_less5_exer1 as base. I have set P0.26 as UART RX. Using the code below...
Hi,
We have 3 nrf5340 LE audio dks. Two of them are flashed as BIS gateways.
One as a BIS headset. Sample used: nrf5340_audio in ncs 2.6.0
I am able to stream audios...
Hi! I am taking reference to following issue :
I have implemented same method as discussed in above link. I am getting message on client side successfully only when code...
Hi, I am trying to set up unit tests for a new zephyr project on the nrf9160. I don't want to run them on the device and instead want to run them from the command line.
...
Hi, I'm currently using nrf5340 and central_multilink and central_uart example to build connection between one central devices to several peripheral devices. But right now...
Greetings
I am following along with the nrf SDK fundamentals, where I am doing lesson 3 exercise 1, which is related to printk. I have flashed my nrf5340 dev kit and it...
Yesterday I opened the nRF Connect for Windows utility and installed all of the pending updates. Now I am unable to flash or debug the project I'm working on using nRF Connect...
Hi All,
I was evaluating the throughput of NRF5340 using the DK. I would like to set the transmission power under 0 dBm of the peripheral device.
However, i was unable...
Hello,
I'm working on a project using the NRF52840-dk module and I'm having a problem with the Bluetooth functionality, during lesson 3 exercise 1. Despite correctly configuring...
Hi,
i just started working with nRF9160dk and i've been trying to implement the GNSS service (testing the Cellular IoT lesson 6 ex 1 exemple), although i've been testing...
Summary: The callback of zb_af_interpan_set_data_indication() seems to be reporting wrong RSSI levels (looks like an overflow) after upgrading from NCS v2.4.2 to NCS v2.5...
Hi, I did some test with IV index using nRF Mesh, here the steps:
provisioned 2 devices in a new mesh (device that have nordic SDK, IV test flag enabled)
from one devices...
Generate Support Information fails dramatically:
I don't remember how to find the log. How many average users would have the slightest clue!!! Please help.
The other...
