Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I've some questions regarding missing or incomplete information in the documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/nrf_modem...
Hello everyone,
I'm working on an Adafruit Itsybitsy nRF52840 Express board and I'm trying to flash the SoC with a J-link EDU mini. I use the nRF Connect extension on VS...
Hi,
I currently do some advertising tests with Nordic's nRF52840-DK and Zephyr. I have one board doing extended advertisements, one transmission every second. By means of...
Hi,
We are using nRF52820 right now and we would like to decrease the current of advertising, I have set the "init.config.ble_adv_slow_interval" to ''1024'' and the average...
ref. an earlier ticket,
I am using ncs 2.0.0 on a custom nRF52840 board
When enabling the CAF BLE state module, I get a build assert error due to
BUILD_ASSERT(!IS_ENABLED...
OpenThread daemon fails to run whenever using the nRF 52840 DK development board but works fine when using the nRF 52840 Dongle. I reinstalled it multiple times and started...
I would like to test he Wi-Fi Provisioning Service sample ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/wifi/provisioning/sample_description.html...
Hi guys,
for a current project, we need access to the local Zigbee binding table of the device (getting information about the binding of the current device).
I've spend...
Hi Nordic,
When I was using NRF52840 for FCC certification, the DTM 8dBm, 2Mbps sideband emission power exceeded the standard.
The antenna matching circuit is to use the...
Hello All,
I am using nrf9160 based custom board with external flash. I am trying to build an application with mcuboot, primary image in internal flash and secondary image...
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am communicating with an Android device (SH-M05) as central.
There are times when I...
Hello,
We are developing a device that uses only NUS (Nordic UART Service) and DFU from the services. In this case, is it possible to implement Pair/Bonded with a client...
Hi,
I am currently trying to get the USB CDC ACM Example on the nRF52 DK to work using the SDK v14.1.0 . But for some reason I can only send/receive data using PuTTY but...
I found this post devzone.nordicsemi.com/.../zephyr-central-to-peripheral-communication , which was helpful to understand the overall structure of both central_uart and central_hr...
I'm trying to build the UART app with SES as per this example:
And I'm getting this error in SES:
Did I miss a step in the installation and setup somewhere?
