I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi.
i am using 5340 + ncs 2.0.2. and gpiote nrfx drvier.
i used gpiote for count encoder
encoder clock speed is about 2.5k and input pint is 2 gpiote pin.
gpiote polarity...
Hello there, I am having problems publishing a message to the server I set up on emqx. Here are the changes I made to the kconfig file (I have not changed the main.c code...
nRF52832にてボタンレスDFUサンプルにEEPROMを実装させたいのですが、
必要なライブラリファイルnrf_cli.cやnrf_queue.cをプロジェクトに追加したところ、 nrf_cli.ｈやnrf_queue.hが「no such file or directory」となり、
ビルドが失敗します。
components...
I've been using the LPUART for comms between the 52840 and 9160 in a Thingy91; this was going well until I changed the nRF Connect version from 1.9.1 to 2.1.2, to resolve...
When I call nrf_pwr_mgmt_run() in my project to put the device into sleep mode, after a short period of time I get the error message:
ERROR 3735928559 [Unknown error code...
Hello all
I am having a problem with nRF Connect SDK where whenever I try to read from a sensor while bluetooth is enables, the software crashes. If I disable bluetooth...
According to the Kconfig documentation, https://nrfconnect.github.io/vscode-nrf-connect/kconfig/install.html , the active board is displayed on the Status Bar when editing...
Running a Thingy:91 now for 4 weeks from batter with one message exchange per hour, it stopped working (NB-IoT mode).
The client (Thingy:91) uses "sendto" and that function...
Was using SDK 1.9.1 up till now, but I migrated to SDK 2.0.0 and I changed my overlay file to add the pin control stuff. I have a nrf5340 and use the app_ns board config....
According the data written to NVM, is there a difference between "%XFSSYNC" and "+CFUN=0" ?
Reading the documentation, I see mainly user configuration be written.
I may...
Hello,
I am trying to add SDCard management, over SPI bus, into my project with nRF5340. When I try to compile, the error is always the same. I am trying the code over the...
Hello,
I have a problem that looks a bit like
devzone.nordicsemi.com/.../nrf52840-custom-board-won-t-boot-without-debugger-reset
For me, to be more precise:
nRF52840...
I just upgraded my environment from nRF Connect SDK v1.9.1 to v2.1.0. This process raised one critical bug, as well as some very important questions:
My projects make very...
