Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I tried to run the llpm (low latency packet mode) code by establishing a connection between nrf5340dk and nrf52840 devices.
I receive a transmission latemcy between...
I've been trying to get breakpoints working on a new nRF Connect project but have been running into an issue: when I hit "Debug" in the nRF Connect plugin in VSCode, the app...
The documentation here:
https://docs.zephyrproject.org/apidoc/latest/group__bt__gap.html#gae11eb8ad254418c38a0e8689df25a159
says, I can call l bt_id_create() before bt_enable...
Hi Nordic,
I am working on code which utilizes the DM library on many devices in a room. Can you please help with a few questions?
Some devices are always initiators...
Hello,
Im currently Implementing Last will and Testament message on my device, Im not using the AWS Libraries here.
Any suggestions on how to Implement this feature...
Hi, from nRF52820 datasheet, some GPIOs pins are stated it use for low frequency I/O only with up to 10KHz.
May I know is that mean these Pins are not suitable for SPI?...
Hello, I am new to BLE and I need help with Battery Service notifications. I am using nrf52840dk, nrf sdk 17.1.0 and I am using ble_app_proximity example which already uses...
Hi all, I have used the nRF mesh app to provision three nodes into a mesh and verified the functionality using the mesh app. I used the export function to dump the mesh configuration...
Hi,
my project is based on the example 'ble_app_proximity' from SDK ver 17.0.2. When I set a longer DEVICE_NAME, for example
the string is cut up after the first 12...
Hello everyone,
I am developing a wearable device using the nrf52832 chip, sdk11.0.0 and s132_nrf52_2.0.0_softdevice.
Because of battery capacity limitation, I have to...
In UART async mode ( CONFIG_UART_ASYNC_API =y) the UART transmit data and receive callback works fine. I've been able to set up the callback and enable the rx.
After switching...
I'm currently setting up an environment in Visual Studio Code because the roadmap suggests going there.
I have experience with Segger and Nordic Segger and with Zephyr....
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi, I am coding an application on nrf connect sdk 1.9.1. which requires to send some data at 25packets per second. and each packet will be ~37 bytes. On the receiver side...
