Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I’m working on a project trying to characterize the range (given a certain transmitter and environment) on the BLE 1 mbps PHY. I’m using a few nRF52840 dongles to do this...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
Hi all,
I trying to use test-harness v2.6 raspi and nRF52840dk to test commissioning. The result is always failure, and the error is timeout
The firmware DK flash is build...
I have a red pulsating light on the dongle.
dmesg shows it is being detected, on Ubuntu 22.04
[203496.636885] usb 3-3.1: USB disconnect, device number 40 [203508.682046...
Hello,
I have a nrf5340 and pc based on Windows OS. I want to transmit information from 5340 to pc at a speed of 300kbps. Here are my two plans:
Using BLE protocol...
Hi all ,
I had my code working on nRF connect 1.6.0 and now had to upgrade it to work with nRF connect 2.1.2.
I read the migration guide for nRF connect 1.x.x to 2.x.x...
I have tested sending NUS data from nRF52832 to laptop (Windows 10 + Intel core i5), but Windows app doesn’t received all NUS data. But When I tested sending NUS data from...
Hello,
I have downloaded the app for linux from here: https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop/Download?lang=en#infotabs
After downloading...
Hi,
I do have a question about the ble_app_uart for central device. Now it is set to make connection with the periheral based on the UUID. I can't find where in the software...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
