Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I was just wondering if the nrf52840 Dongle is in some ways inferior to the other development boards in terms of its capabilities?
As I was going through the examples...
Hi,
I am using a nrf528409dk for my application development using nCS. I have various features from which I need to understand how to add some high priority features into...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
We want to start with ble_app_uart example for our product but it the firmware halts at CRITICAL_REGION_EXIT() in nrf_sdh_enable_request.
We are using the example from 17...
Hiii, is there any libraries or example to read nfc tag through clrc663 nfc reader, could any one direct me to the any solution
thanx in advance
suprith
I am having problems setting up UART communication between nrf9160 and nrf52840 on Thingy91. My set up consist of a Thingy52 and a Thingy91. I am using ncs version 2.0.1....
Hi,
I've been working on Open Thread recently. I found that after I send provisioning request, even though there are 3 servers "enabled provisioning", the callback function...
Hi,
I am trying to setup a raspberry pi 0-W for flashing nrf devices. But nrfjprog doesn't seems to work.
I am using Raspberry Pi OS (32-bit).
I have fetched Segger...
