I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I'm developing an application that will include over the air updates. I read the infocenter information about how the dfu works, with either dual-bank or single-bank...
Hi,
As I am using the nRF52840 DK for a project, so I followed the instructions for setting up nRF Connect SDK as it's the main SDK going forward: nRF Connect SDK and nRF5...
Hi, How can I get the RLOC16 or similar ID from the CoAP clients connected to my CoAP server? I need to get this information from the messages that the clients send.
Cheers...
My BLE application needs to communicate with another µC using serial UART - so I started my app based on the sample in bluetooth/peripheral_Uart I'm have a nRF52_DK board...
Hello I have flash memory via SPI on the custom board. It works on SDK v2.0.2 properly and doesn't works on SDK v2.1.0. Flash memory defined in Device Tree as mentioned below...
Dear Sir.
we are porting some projects from nRF5 to Zephyr and the UUID/handlers table consume more memory. What is the best practice? we are trying to do the same things...
Hi Nordic community,
Let me ask a question.
I can run AT+RUNIMPULSE command via UART cable successfully, but I cant write it using BLE. For example using Nordic nRF connect...
Hi,
I have tried setting a custom network name by adding
CONFIG_OPENTHREAD_NETWORK_NAME = "MILIEU_OTNET" to prj.conf of both coap client and coap server. But they always...
Hello everyone,
I am trying to use the S340 softdevice in order to connect to an ANT+ HR. I would like to use proximity search.
It works fine for the first device in range...
HI
After the connection between the light-bulb and the Zigbee-Coordinator is completed, it is observed from Sniffer that both parties will broadcast regularly (as shown...
Hello,
I'm writing my own UARTE library because I need some functionality not offered in the SDK. But I came across a hardware behaviour I can't explain.
In my understanding...
Hi,
i use NRF52832
I used bootloader V5.4 and I don't see the prints I used SEGGER workspace
in sdk the settings set #define NRF_LOG_DEFAULT_LEVEL 4
what can I do...
Good day
I have been testing sample code code, but when compiling I get this error
nRF5_SDK_17.1.0_ddde560\components\libraries\uart\retarget.c:101:23: error: unknown...
I am plugging the nrf52840 Dongle to the USB port, the computer beeps as it recognizes a new USB device, but when I open the Programmer app from the NRF desktop connector...
