I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
What would be the best orientationg for data acquisition with the Thingy's 53 microphone? I see the plastic case has some slots.. Those up or down? Outwards or inwards...
Hi,
In the documentation of SDK 17.1.0 it is stated that only s132 v7.2.0 is supported. I want to update from SDK 16 to 17, but don't want to update softdevice, currently...
Using the nRF9160-DK together with the Power Profiler Kit 2, I observe sometimes a longer period (1 minute) of a 50mA consumption before entering PSM mode.
Is there a explanation...
Hi,
Our application has a GUI, the UI data is stored in the QSPI flash and it is independent of the firmware,
We program the QPSI flash via the PC tool in the development...
Hi , I got my Nordic Thingy : 53 I wanted to connect other sensors to the Stemma/qwiic port of it . Can you share some documents or example of how to connect multiple sensors...
Hello, I have a problem regarding production flashing a nRF52811 device. We are using a Segger Flasher Compact, but I also tried a Segger J-Link Compact. To flash we are using...
We used 52840 chip to produce a near field communication module, the antenna is on board antenna, some problems occurred during the verification process, can your engineer...
hello Nordic
i work on nrf52832, trying to run it with zephyr application
one board runs fine (more/less, there are some MPU FAULT issue that i am facing with no luck...
Hi everyone,
I have some issue when my device is in very low temperature of -60°C / -70°C.
We use an NRF52832 (SDK 15) on modules (BMD-300 frome UBLOX formely RIGADO...
I'm working with lsm6ds33 sensor using lsm6ds3 driver I get some results, but they are ae rarely modified and didn't follow the IMU motion so how can I correct this.
(The...
Hello,
When I use sntp to get the timestamp from time3.google.com, getaddrinfo returns a -10 error. nrf9160 device also reboots automatically, why did the device reboot...
Power Profiler app v3.5.0 running in nRF Connect for Desktop v3.12.0 in Ubuntu 220.4 reports "No Supported Devices Connected".
I have used my PPK2 successfully recently...
Hello team,
I was not able to receive a suitable reply for this post for almost two weeks. I started thinking the engineer had gone for vacation. That is the reason I...
Hai, how you doing?
I am facing difficulty in trying to connect ble devices with windows 10. I am using BLE dongle APLIC WDP 304747 (Also tried another couple of BLE dongles...
In nRF Connect SDK 2.1.0 the devices in the DTS file are missing the "label".
For example, in nRF Connect SDK 2.0.0:
gpio0: gpio@842500 {
compatible = "nordic,nrf-gpio...
