Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
about ANCS categoryID 12
I see this website
https://www.linkedin.com/pulse/working-ble-profile-apple-notification-center-service-sarda
have any one know
how to get...
Hi Nordic,
1. Dual Uart this code i used
2. Its working fine and am getting output also
3. But i have doute its printing from uart0 but i want from uart1
4. For that...
Hi,
currently, it seems the CIS bidirectional mode is not supported. I understand that telephony and these profiles then are not able to be evaluated like in a "real setup...
I'm looking to develop a board using the nRF52810 SoC, and am prototyping it on breadboard to start with. The circuit I've set up so far is the same as the reference circuitry...
Hello,
I have been trying to resolve an issue for a few days now. Here is what I'm trying to do.
1. initialize gpiote and tie a pin to an interrupt handler
2. initialize...
Hello folks!!!!
I'm making a similar kind of project available in example and named as ble_app_beacon but the problem is that I'm using PCA10100 board and there's no guide...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0
One of my customer expects such a scenario. 1) BLE accept first connection. 2) If BLE have another connection, BLE disconnect...
Hi I m trying to implement mass storage on the arduino nano 33 ble sense board(nrf 52840) and I2c together. I m using the sample from zephyr and it will not mount the file...
I want to install the NCS V2.1.0 with Toolchain Manager V1.1.3. But after I installed, I found that there is only a toolchains folder and a empty .west folder in my intalllation...
hi
I have a question about uart receive.
The UART example receives data based on special characters or the length of the received data to determine whether it is a string...
Hi
We have been using the Online Power Profiler to estimate the current draw from nRF52805 during BLE activity. Especially estimating the potential peak current draw (from...
I bought a nRF52840 DK, and followed the UG for nRF BLE sniffer v4.0.0. I was able to see the sniffer interface in Wireshark on my Linux machine, but when I start capture...
Hello!
I am trying to install MCUMgr on MACos.
I install the Go Programming Language and then follow this: https://docs.zephyrproject.org/latest/services/device_mgmt/mcumgr...
(I was asked to create a new post for this specific query. The original post where this investigation started is here: Async UART and shell module in Zephyr on nRF52480 )...
I've just built up a batch of custom PCB's we designed using the nRF52832-QFAA IC's. I'm attempting to program these with the nRF52-DK, and am following the connection diagram...
