Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have a few queries:
I need to confirm that does Thingy53 board support TensorFlow lite. So, for my ongoing project, I am using TensorFlow to develop my code...
Hello,
I am facing an issue at running otbr docker conainer on my RPi4 with nRF52840 Dongle as an RCP device . I am getting this error on the logs: Aug 24 16:05:07 0e6bb978e199...
Hi!
I have tried to get the secure_bootloader working on the nRF52820, but I think the linker settings are not correct yet. Maybe someone here has already written a bootloader...
Hello,
I am trying to build OpenThread Radio Co-Processor (RCP) firmware for nRF52840 Dongle with the new nRF Connect SDK v2.0.2. My VM is running Ubuntu 20.04.3 LTS with...
Hello!
I have an application that makes use of the function sd_ble_gap_conn_evt_trigger_start() , present in v7.3.0 of the S113 , S132 , and S140 SoftDevices. Here's the...
Hi,
1. I can use Programmer in nRF Connect for Desktop to flash the hex file ( nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images\ble\nrf52832sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Greetings,
I want to write the nRF Connect SDK v2.0.0 sample "nrf9160/https_client" to the nRF9160-DK, but when I use "Flash" in Visual Studio Code, the following error...
Hi,
I'm designing a drone based on these three Nordic IC:
nPM1100
nRF5340
nRF21540
Let's Start with nPM1100:
Based on this Reference circuitry
I based my...
On SDK 2.0.2, I was able to load peripheral_uart with CONFIG_BOOTLOADER_MCUBOOT=y and successfully update both the app core and net core using the thingy53. However when moving...
Hey,
I bought a device which uses the N52832 SoC, Im gonna attach a photo of the device. Is it possible to get the code from the device, modify it and then upload it to...
Do you know of any way of reading the installed modem version of an un-locked nrf9160 through the j-link programmer. I would like to conditionally program the modem firmware...
