I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
Hi Team,
We are working on nRF52840 SOC with BLE functionalities.
We need the mechanism for to find out the BLE or BLE Stack is in Hanging state before the processor is...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
In order to add the BLE DFU service, I need to increase the GATT table size and therefore memory as mentioned here: .
However, when I tried to increase the file ble_app_uart_gcc_nrf52...
Try by changing the RAM size but it didn't worked.
<info> app_timer: RTC: initialized. <error> app: ERROR 4 [NRF_ERROR_NO_MEM] at :0 PC at: 0x00000000 <error> app: End of...
Hello, I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hello Nordic Team,
I have an issue on one of my 10056 DK. The DK is connected to a development PC, appears in device manager as a Jlink CDC UART port, and as a mass storage...
In the Zigbee framework, what is the purpose of the return variable from zb_osif_sleep() ? The "documentation" for Zigbee seems to implement a "guess and figure it out for...
Hi,
I'm following the ble_template example on my custom board. I'm having an issue with waking up (soft reset) the device from sd_power_system_off. I can power off the system...
Hi ,
We are using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip. Does this sdk and soft device supports extended advertisement?
I could able to enable this...
