Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I'm trying to program an nRF52810 on a custom PCB using the nRF52-DK and am getting this error ((0x4) Lowlevel error: Unknown value (ffffff24)) when connecting with nRF Connect...
Hi there,
I'm working on something with hard real-time requirements - for this and a number of other reasons, I'm writing directly to the registers.
I'm trying to generate...
Hello,
Is it possible to multiplex coded phy and 1M for advertising and connections on zephyr? If so, do you have any available sample code or timing requirements?
...
I'm having a hard time wrapping my head around how to configure my LIS2DH accelerometer for 6D orientation detection with Zephyr. How would I manipulate the registers of my...
ncs 1.5.1, using SES, the example for zephyr samples/boards/nrf/nrfx/src/main.c github URL: github.com/.../main.c
does not work for me; while the 'button_handler' gets called...
Hello, I want to make multiperipheral system with nRF52840 (Im using 4x nRF52840DK). Im using latest SDK17. I wrote criteria i want to put to this system below:
1. Devices...
My question is very simples. If I have to start with a new design, is better for me to use the softdevice implementation or is better to use the zephyr once ?
The evolution...
Hi team,
My customer is using DTM for the test and they want to know how to change PHY and radio channel setting for the DTM, could you please help to clarify?
Thanks...
in sample ,prj.conf had configure ble device name using below define :
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service" ,
in hci_core.c function bt_enable() use set_bt_name...
Hi Nordic,
In this question: https://devzone.nordicsemi.com/f/nordic-q-a/56529/how-to-check-or-read-the-list-of-bonded-device-from-nrf52832 It was discussed to update...
Is it possible to use both Zigbee & BLE MESH at same time?
Actually we are planning to use NRF52840 for our next project. In which BLE MESH will be used for BLE mesh device...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
