I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello Nordic Experts,
I almost finished the development for my mesh project with nRF52840. But I faced some t ricky issues when in mass production. that is the time for...
Hi,
I am using SDK15.3.0 and s132_nrf52_6.1.1_softdevice. (nRF52832)
Getting higher current consumption ( 300uA ) while using the PWM library. ( https://infocenter.nordicsemi...
Hello, everybody.
I bought the nrf5340-dk board and tested the zephyr sample code. The Blinky code is worked. I tried the beacon sample code. But it is not worked. I think...
Hello ,
I have interfaced one NTC sensor with above attached image and below information :
SAADC pin : AIN2 ( NTC - pin )
VCC_nRF voltage = 3.3V
R14 = 51KOhm , 0.5...
Hi Team,
We have some application for using the oversampling code but we are facing some issue in that, we try to use the oversampling example to ours code but its calling...
Dear sir,
When use the template project(Which is in peripheral) for UART tx & rx is not working in without debug, but if i use base project(Like uart) file it is working...
Hello, I've seen some similar questions about resets after downloading firmware, but haven't been able to find the solution to my problem.
I'm using a Minew MS88SF3 NRF52840...
Hi,
We have a working application that allows FOTA when using the SDK 15.2 bootloader. We have recently tried to migrate this to SDK 17.0, and everything works except for...
Hi
I needed assistance to get the SKY66112-11 FEM working with the Radio Test Example, for certification testing (FCC, CE etc). I am using the NCS 1.5.1 SDK. I am using...
Hello,
I am using example code of MAX30101 Pulse Oximeter sensor with nRF SDK v1.5.0 on board NRF5240DK. I copied the example from the ncs \ v1.5.0 \ zephyr \ samples \...
Hi,
I am doing Mesh DFU , but there only have mesh bootloader hex file , I need to change bootloader source code, does there have some example? or where can I get the source...
Dears,
I didn't find any size information about IN105 & AN118. Would you kindly please help to provide a complete reel size drawing? Many thanks!
Best Regards!
Ricky...
I started working with BLE and I have some trouble understanding few things. The connection interval happens every X ms, that is set by master, usually the default is lowest...
Hi,
I want to combine ble_app_blinky and uart_pca10056 examples to get the uart communication(between terminal emulator and application) in ble_app_blinky app. I followed...
In the piece of code, where Ble_Stack_inti has been defined, err_code = nrf_sdh_enable_request(); DISPLAY_ERROR_IF_ANY(nrf_sdh_enable_request) APP_ERROR_CHECK(err_code); is...
